Our world is full of interesting things, even a small trifle can become a whole treasure for some person. Every day on our planet something new and exciting is invented, put into production, and then pleases the whole world. We know that nowadays many interesting things, puzzles are being created, and today we will tell about one of them. A Chinese finger trap is a trifle, but how nice it is to experience new feelings and try to outwit an unwise contraption.

What is a home finger trap made of?

This is very simple craft, despite all its mystery. We just need a little time and a sheet of paper from which we will cut the strips we need. If not big paper, then you can use the ribbon to decorate gifts, but not very wide.

How to make a DIY finger trap?

Well, let's get down to the craft. It is not heavy, so even schoolchildren can handle it.

1. We prepare four pieces of paper or tape, 1 cm wide, long at arm's length.

2. We take two tapes and fasten their ends together unevenly, at an angle of 80 degrees. We do the same with the other two pieces.

3. Now we should take a small round stick, the diameter of the finger. We attach our tape to the cylinder. Glue one glued end of two tapes to the cylinder. The second to the back of the cylinder, symmetrically to the first.

4. We begin to wrap the cylinder. We wrap one strip, then stretch the second behind it, and so on until the ribbon runs out. Here's what we got. If the braiding is not correct, the trap will not work!

5. The end of the tape should also be fastened together.

6. We take out the cylinder and our trap is ready!

How do I use the trap?

Using this trap is very simple - stick your left index finger on one side and your right hand on the other. Then try to pull it out, it is unlikely that you will succeed, because that is why it is a trap.

This Chinese paper strip toy is a finger trap, traditionally made from bamboo, but this funny toy can be easily made from a regular sheet of paper. Put your finger in this pretty paper tube and then try to pull it out. The harder you pull, the tighter the trap will hold you! Famous people indulged in this ancient toy! To be free, all you need is a little gentleness. Press it gently with your finger, and do not pull on the other end, and it will slip out immediately!

This paper strip toy is cheap, and is easily made with the materials and tools you already have. This makes it ideally easy to learn, like a DIY birthday present. Place it in a treat bag, or use it to decorate the table.

How to make a Chinese paper strip toy - finger trap?

Materials:

Standard size paper (writing or A4) in contrasting colors as desired.
Glue
A wooden dowel, rod, or pencil that is slightly smaller in diameter than your fingers. You can also roll up a piece of paper and hold it together to create a rigid shape with a suitable diameter.

Instruments:

Ruler
Buttons or ribbon
Scissors or craft knife and cutting mat.

Steps:

1. Cut 4 strips of paper, 1/2 "wide (or 13mm) along the long edge of the sheet of paper.

2. Make two L-shaped pieces by gluing the two paper strips together at a 90 ° angle.

3. Temporarily attach L-shaped paper strips to opposite sides of your wood rod using buttons or tape.

4. Weave the paper strips of the toy together as shown below, pulling them slightly around your mold as you go.

5. After you have woven the finger trap to the desired length (approximately 5 1/2 "or 14 cm), glue the strips of paper together on two opposite sides where they overlap.

6. Peel off the woven paper toy mold, and cut off the excess paper of the strips.

Based on materials from www.makepopupcards.com

An interesting puzzle for those who like to break their heads. This amusing toy has a small secret that is easy for an adult to guess, but a child is unlikely to find a solution to this problem immediately and on his own. If you have a desire to surprise someone, watch the video tutorial on how to make a finger trap. In China, these traps were woven from bamboo, so it was almost impossible for a person who fell for it to pull out his fingers without knowing the secret. This video tutorial offers a simple paper option.

To make this Chinese entertaining toy, you will need two strips of paper, glue and a marker, or another tube-shaped object.

Homemade Chinese Finger Trap

The Chinese finger trap is a typical joke. You give this to your friend and ask them to stick their fingers at both ends of the device. As they are pulled outward, the cylinder narrows, and the victim is almost unable to escape. The finger trap was originally made from bamboo, but in this tutorial, I'll show you how to make one out of paper. It is very easy to do this by simply interweaving the strips of paper around the cylinder. It takes about 10 minutes to make it the most in a simple way and works very well.

Step 2: make a cylinder

If you already have a dowel, handle, or something the same size as your finger, you can skip this step. To make your cylinder, simply roll up a piece of scrap paper and use tape to keep it from unrolling. The cylinder should be slightly less than your finger's width.

Step 3: prepare your strips

Now you need to cut four strips of paper, preferably two of each color. Cut your strips from the long side of A4 piece. The width of your stripes depends on the width of your finger. I used strips 1.5 cm wide, but my fingers are quite thin. You can always experiment. After you cut the strips, you will need to use a Blu-Tack to glue them perpendicularly at one end so that you get two right angles as shown. You need to have two identical right angles with the same color on the top. After that, use Blu-Tack again to glue the two right angles to the top of the cylinder. therefore they are opposite. Again, like the picture.

Step 4: weaving

Here you need to start weaving the strips around each other around the cylinder. This can be done by taking one stripe going in one direction and placing it under a stripe of a different color, and then on a second stripe of a different color. Repeat this with all the strips until you are almost out of paper. This can help when you are weaving so that all the strips fit snugly against the cylinder.

Step 5: Tigring

Use Blu-Tack again to glue the strips together at the end, as at the beginning. Then remove the Blu-Tack at the top while holding the strips in the cylinder and remove the finger trap from the cylinder. Now for each endpoint, remove the Blu-Tack separately and pull the strips tightly, then replace the Blu-Tack. Check the width by sticking one of your fingers into it, if you cannot insert it, you may need to loosen it.

Step 6: glue the ends

Now that you are happy with your finger trap, you can remove the Blu-Tack and glue the ends together. Remove all excess paper and you're done! Now go and prank your friend. Since the trap is made of paper, it can rip if your friend is too rough, but that doesn't matter because you can always make a new one.

Step 7: more stripes

If you would like to make a more unusual finger trap, you can use more strips to make it. Initially I used 4 stripes of each color. More stripes should be proportionally thinner. Don't just accept width as I do. Measure them.

), TV program of terrestrial and ADSL-TV channels, the freshest and most interesting news from the world of high technologies, the most original and amazing pictures from the internet, big archive of logs per last years, mouth-watering recipes in pictures, informative. The section is updated daily. Always fresh versions of the best free software for everyday use in the section Required programs... There is almost everything you need for your daily work. Start gradually abandoning pirated versions in favor of more convenient and functional free counterparts. If you are still not using our chat, we highly recommend getting to know him. You will find many new friends there. Moreover, it is the fastest and efficient way contact the project administrators. Section continues to work Antivirus updates- always up-to-date free updates for Dr Web and NOD. Didn't have time to read something? Full content creeping line can be found by this link.

Finger trap

Master class on creating Chinese finger traps. You will learn how to play a trick on your friends.

Asia is famous for its puzzles and quirky games. Even in ancient times, an entertainment called "finger trap" appeared in China. Its essence is simple: a person inserts his index fingers into a braided tube, and then cannot take them out. And the more efforts the victim makes, the tighter the trap is tightened, and only the manufacturer of this "toy" knows the secret, thanks to which one can free himself.

The way to make finger traps is not too complicated. In the old days in China, bamboo bark was used for this, the trap turned out to be very strong, and the grip was the strongest. Today you can make such a puzzle toy out of plain paper. Chinese finger traps are not expensive, but the manual version is much more interesting, and you can make it in a variety of colors.

At the first stage of manufacturing, you only need paper of two colors (it will be more convenient to make and it will look more interesting), scissors and ordinary glue. DIY finger traps are made from four thin strips of paper, two of each color. You need to cut strips 12 millimeters thick along the entire length of an A4 sheet.

You don't need much precision here, but try to cut the strips neatly. Of the four strips, you need to glue two corners: glue the strip of the second color to the strip of the same color at an angle of 90 degrees. Do not use too much glue to prevent the paper from getting wet. This is the first step in how to make a finger trap.

For the second stage of work, you will need any cylindrical object that can be found in the house. To determine the length, simply bring your two index fingers together with the tips. Your cylinder should be the same length or slightly longer, but not less. If you make a trap as a gift little child, take this into account in the size of the cylinder.

The Chinese finger trap is completely safe, especially in a simple paper version, so do not be afraid to give this thing to children of any age. The thickness of the cylinder is one and a half centimeters or the diameter of a finger. A body from a thick marker is fine. Take small pieces of insulating tape, loop them. The end result is a small cylinder that is sticky on all sides. They need to be glued to your paper corners from the back.

The third step of the way to make a finger trap is assembly. Glue the blanks to the cylinder from one edge, but from different sides in diameter. The corners should protrude slightly outward. Now the hardest part is braiding. Proceed in the following sequence. If the Chinese finger trap is made in red and yellow, then the weaving will be as follows: from one side, pass the red ribbon under the yellow one from below and press it with your finger, do the same on the other side, then turn the cylinder again. Then thread the yellow tape below under the red one, clamp it and turn it again.

Alternate the colors until all the paper is braided. Gradually tighten the weave by sliding it up. In the end, you just need to glue all the paper ribbons to each other in turn. Cut off the free ends, take out the electrical tape, shake the cylinder out. Your DIY finger trap is completely ready to use.

The trap will work if you braid the ribbons correctly. The essence of the puzzle is very simple: it is simply impossible to remove your fingers with sharp jerks. To free yourself from the trap, you need to squeeze a certain strip of paper on each side and gently pull out your fingers one at a time. This effect is based on simple physical laws, but it can surprise anyone.